BDFHYK E2361M fuel pump module for 2003–2004 Ford Expedition 4.6L

E2361M pump sender reservoir strainer float and tank seal assembly

E2361M four-pin connector dual fuel outlets and flange details

E2361M fuel-level sender float arm and reservoir construction

E2361M Ford Expedition 4.6L trim and fitment reference

E2361M FG0862 Ford OE interchange and module dimensions

Ford Expedition Fuel Pump Module Assembly 2003-2004 4.6L V8 Replacement E2361M BDFHYK

$58.89

Product Detail

Type Fuel Pump Assembly
SKU BDDLZ-BD-05-10488-FP
Make
- Ford
OE Number FG0862,104GE,1AMFP00161,2L1Z 9H307-CA,2L1Z 9H307-CB,2L1Z 9H307-CG,2L1Z 9H307-CH,2L1Z 9H307-CJ,4010370,525-2590,67222,953-4007,A30097,DFG0862,E2361M,M2425962,P76023M,PFS-1015,PFS-454,RE0877S,SP2361M

Trust & Assurance

Free Shipping · 3–7 Business Days

12-Month Warranty

30-Day Return

Secured Payment

Technical Specifications

Part Number	E2361M / FG0862
Product Type	In-Tank Fuel Pump Module Assembly
Installation Location	Inside the fuel tank
Fuel Type	Gasoline
Application	2003–2004 Ford Expedition
Engine Coverage	4.6L V8
Trim Coverage	Selected XLT, XLS, NBX and XLT Sport configurations
Module Functions	Fuel delivery, reservoir pickup and fuel-level reporting
Fuel Level Sender	Included
Float and Reservoir	Included
Strainer and Seal	Included
Fuel Outlets	Two outlets; compare diameter and orientation
Electrical Connector	Four pin terminals; compare connector keying
Fuel Tank Pressure Sensor	Not included
Drivetrain and Tank Check	Verify 2WD or 4WD, trim, tank depth and original module
OE References	E2361M, FG0862, SP2361M, P76023M, 2L1Z-9H307-CA/CB/CG/CH/CJ
Fitment Priority	Model year, 4.6L engine, trim, drivetrain, tank, OE and physical layout
Installation Note	Clean the tank, install a new seal and reconnect both outlets correctly
Diagnostic Note	Test pressure, voltage, ground, fuse, relay, wiring, lines and sender circuit

Extended cranking, low measured fuel pressure, hesitation under load, intermittent stalling, or an inaccurate fuel gauge can indicate an in-tank module fault after the fuse, relay, power supply, ground, wiring, and fuel lines have been tested. This E2361M replacement module is intended for specified 2003–2004 Ford Expedition vehicles with the 4.6L V8 gasoline engine. Confirm the model year, trim, drivetrain, OE number, four-terminal connector, two fuel outlets, flange, module height, sender arm, and tank configuration before ordering.

Fuel Pump Module Fitment for 2003–2004 Ford Expedition 4.6L

This complete in-tank module is organized for specified Expedition 4.6L configurations, including applicable XLT, XLS, NBX, and XLT Sport vehicles. Similar 5.4L or different tank modules are not interchangeable solely because the flange appears similar.

Fitment Verification

Confirm the 2003 or 2004 model year and 4.6L V8 gasoline engine.
Match E2361M, FG0862, SP2361M, P76023M, or the verified Ford 2L1Z-9H307-CA/CB/CG/CH/CJ number.
Compare the four-pin connector, two fuel outlets, flange, reservoir, full module height, and float arm.
Verify trim, drivetrain, tank depth, sender calibration, and vapor-sensor provision before installation.

Module Functions and Included Components

Electric in-tank pump supplies fuel to the engine-side delivery system.
Fuel-level sender, float arm, reservoir, inlet strainer, and tank seal are included in the verified FG0862 configuration.
Two outlet connections must be returned to their original positions.
The verified configuration does not include a fuel-tank pressure sensor.

Symptoms and Diagnostic Checks

Measure fuel pressure before replacing the module. Test voltage and ground under load, inspect the fuse and relay, and check both fuel connections and the electrical connector. Tank contamination, restricted lines, sender faults, EVAP problems, or engine-management faults can create similar symptoms.

Installation Notes

Relieve fuel-system pressure and disconnect the battery before opening the tank. Clean the tank and sealing surface, install the correct new seal, keep the float arm clear, and connect both outlets correctly. Prime the system, inspect the flange and lines for leaks, measure pressure, and confirm normal gauge operation.

What’s Included in This Fuel Pump Assembly

Complete fuel pump module
Integrated fuel level sending unit
Fuel strainer (filter sock)
Housing and mounting components

This fuel pump assembly is designed as a direct replacement unit that restores proper fuel delivery and fuel level monitoring.

Estimated Installation Time

Professional mechanic: 1–2 hours
DIY installation: 2–4 hours

Fuel pump replacement usually requires accessing the fuel tank or service panel depending on the vehicle design. Always disconnect the battery and relieve fuel system pressure before installation.

Pump Only vs Fuel Pump Assembly

Option	Description
Replace Pump Only	Lower parts cost but requires disassembling the existing module and reusing older components.
Replace Complete Assembly	A complete module designed for direct installation, helping restore reliable fuel delivery more efficiently.

Most modern vehicles use integrated fuel pump modules, which makes replacing the full assembly the more reliable solution.

Q: Which vehicles use the E2361M module?

A: It is intended for specified 2003–2004 Ford Expedition vehicles with the 4.6L V8 gasoline engine.

Q: Does it fit the 5.4L Expedition?

A: No. The 5.4L application uses a different module family, including E2360M in specified configurations.

Q: Can fitment be confirmed by year and engine alone?

A: No. Verify trim, drivetrain, fuel tank, OE number, connector, both outlets, height, and float arm.

Q: Is the fuel-level sender included?

A: Yes. The verified FG0862 configuration includes the sender and float arm.

Q: How many fuel outlets should be present?

A: The verified module uses two outlets. Their diameter and orientation must match the original assembly.

Q: What connector should be checked?

A: Compare the four-terminal connector, keying, and locking tab with the removed module.

Q: Is a fuel-tank pressure sensor included?

A: No. The verified FG0862 configuration is listed without a vapor-pressure sensor.

Q: Are the strainer and tank seal included?

A: Yes. The verified module package includes the inlet strainer and tank seal.

Q: What should be tested before replacement?

A: Test voltage and ground under load, fuse and relay operation, fuel pressure, wiring, both lines, and sender continuity.

Q: What checks are required after installation?

A: Prime the system, inspect the flange and both outlets for leaks, measure pressure, and confirm normal gauge operation.

Returns & Refunds

We accept returns within 30 days of delivery for eligible items. If the product is unused and in original condition, you may request a return according to our refund policy. Full policy details: View Refund Policy . We recommend contacting our support team before initiating a return to ensure the fastest resolution.

Customer Support

If you purchased the wrong part, received an incompatible item, or need installation assistance, please contact us directly.

Email: service@bdfhyk.com

Business Hours:

Mon–Fri 9:00–18:00 (GMT+8)

Mon–Fri 19:00–04:00 (UTC−6 / CST)

Manufacturing Standards

Direct Factory Supply, Cost Saving
Integrated R&D, production, and warehousing. Eliminate middleman markups: same quality at lower prices, superior quality at same prices.

Precision Inspection, Commitment to Excellence
Rigorous inspection process, international certification standards. Each product includes individual inspection.